40+ Point Heat Pump Fall Tune-Up/Check-Up


Click below for information on:

Unlike "Murphy's Law" which nearly everyone knows that states "if a thing can go wrong, it will... and at the worst possible time" many people choose to ignore "The Law Of Moving Parts" that states "that moving parts someday will wear out and like Murphy's law, will wear out at the worst possible time, leaving you in the cold without heat.
40+ Point Heat Pump Fall Tune-Up/Check-Up

The following Special Discount for our 40+ point check-up/tune-up for heating systems has a strict time limit. The effective dates are 8/15/11-10/31/11.

The complete description of a 40+ point check-up/tune-up is for a heat pump system and the benefits that accrue.

	Work Performed	Benefits
1.	Check thermostat	Improperly calibrated thermostat affects comfort and operating costs.
2.	Start unit	Verify unit is operational before tune-up takes place.
3.	Check return air filter	Restricted filter causes unit to waste energy and shorten compressor life.
4.	Routine cleaning of evaporator coil**	Dirty evaporator coil decreases efficiency and can lead to compressor failure.
5.	Clean condensate drain**	A plugged condensate drain can cause expensive water damage.
6.	Check condensate pan and fittings for leaks	A cracked pan or loose fittings can cause expensive water damage.
7.	Check blower wheel	Dirty blowers reduce air flow; increases operating costs and can lead to compressor failure.
8.	Check blower motor stability	Dirty motors are less efficient and will fail sooner.
9.	Check blower motor amp draw	Ensures optimum performance; protects equipment.
10.	Lube motors & bearings	Improperly lubricated rotating equipment will eventually fail.
11.	Check belt, pulleys and alignment	Avoids costly service calls, saves money on utility costs.
12.	Check total electrical consumption	Ensures optimum performance; protects equipment.
13.	Examine parts for visible wear	Avoids costly service calls.
14.	Check and secure all panels	New systems have a blower door safety and will not operate if door is not properly in place.
15.	Examine all electrical connections	Extends life of system; ensures safety.
16.	Check unit disconnect switch	Worn, overheated disconnect blows fuses; potentially dangerous.
17.	Check temperature difference across coil	Temperature difference indicates production and capacity of unit. Also affects comfort level.
18.	Remove debris around outside unit	Promotes Efficiency. Prevents damage to equipment.
19.	Routine cleaning of condenser coil	Dirty condenser coils raises refrigerant pressures increasing electrical costs.
20.	Check condenser fan motor stability	Prevents costly service calls.
21.	Check condenser fan motor amp draw	Ensures optimum performance; protects equipment.
22.	Check condenser fan blades for vibration	Prevents damage to unit and costly service calls.
23.	Check reversing valve	Improperly operating reversing valve wastes energy.
24.	Check crankcase heater	Crankcase heaters that do not work lead to compressor failure.
25.	Check relays & contactors	Worn contactors and loose connections can lead to motor and compressor failure.
26.	Check capacitors	Bad capacitors lead to compressor and motor failure.
27.	Check all safety devices	Keeps unit in safe operating condition.
28.	Test time delay	Prevents unit from starting under load when power has been temporary interrupted.
29.	Check defrost assembly	A defrost timer that does not work correctly causes loss of heat and can shorten life of compressor.
30.	Check all controls	Extends the life, saves money, and prevents failure.
31.	Test refrigeration metering device	Blockage or improper operations of metering device reduces cooling capacity, increases fuel costs, and shortens system life.
32.	Measure operating pressures with gauges	Improper refrigerant charge can cause compressor shut down.
33.	Check noise and vibration levels	Increases comfort & extends life of equipment.
34.	Check compressor amp draw	Ensures optimum performance; protects equipment.
35.	Make final operations test	To ensure optimum performance.
36.	Wax outdoor unit**	For weather protection and extended life.
37.	Record system operation	For Home owner's information and records.
38.	Explanation of tune-up results	Explanation of work performed in tune-up and results.
39.	Advise improvements as needed	To allow you to gauge effectiveness, efficiency and potential need for repair or replacement.
40.	Conclude Transaction	Answer questions; collect for work performed, signature(s) on invoice, leave customer copy of tune-up, and make appointment for any additional work required.

41.	Check Reversing Valve	A reversing valve that is not operating properly wastes energy and causes a loss of heat.
42.	Auxiliary Heat Strips	Improperly operating they cause loss of heat or increase electric cost higher than necessary.
43.	Check water temperatures***
44.	Check water flow***

*** Water Source Only
** If feasible and where accessible.


The regular cost for the heating "tune-up/check-up" is..................................................................................		$150.00

Less 40% Fall discount if ordered before 9/13/11 A Savings of $60.00. Your cost is.............................		$90.00

Less 30% Fall discount if ordered between 9/14/11 and 9/30/11 A Savings of $45.00. Your cost is.............................		$105.00

Less 20% Fall discount if ordered between 10/01/11 and 10/31/11 A Savings of $30.00. Your cost is.............................		$120.00


Take an Additional $5.00 OFF if ordered On-Line!
(additional discounts for multiple zones)

TO ORDER A HEATING "TUNE-UP CHECK-UP" CLICK HERE

P.S. Do your friends and family a favor. E-Mail them the link below so they too can get these Buying Secrets and other answers to their HVAC questions....They will thank you for it!

www.climatemakers.com

Only one coupon per call, email or website request. Coupon can not be combined with any other offer or special promotions. Offer limited to homeowners only. Oil systems, builders and commercial buildings specifically excluded.